Electro-star | Hamilton Electrical Contracting - • Panel and Service Upgrades  • Pot Lights, Track Lighting, Chandeliers, Ceiling Fans and Ac • Flood Lights, Landscape Lighting  • Receptacles and Light Switches  • Knob and Tube Replacement  • Fuses to Breaker
Circuit Breaker Tripping off:

Electrical Panel Breaker

 circuit breaker is designed to trip off when it detects too much power running through the wire it’s protecting. There are three main reasons circuit breakers trip off:

1. There is a short circuit.

2. There is an overloaded circuit.

3. The circuit breaker is broken.Short CircuitsShort circuits occur when two electrical wires accidentally touch each other.

 A short circuit will immediately cause one of your circuit breakers to trip off or one of your fuses to blow.To fix a short circuit, ask yourself this question: “What was happening right before the short circuit?”

 If you had just plugged something into a receptacle (outlet) or turned on a light or an appliance, then this gives you a clue as to what caused the short.If you just plugged in an iron, for instance, you can simply un-plug the iron and then re-set the circuit breaker or replace the fuse. 

If everything is now OK, then your electrical system is fine – and it’s time to get a new iron!If, however, you can’t find anything plugged in which is causing the problem, then it’s time to call a good electrician to locate and repair your short circuit.Overloaded CircuitOverloaded circuits occur when too much power is runng.

Lighting Problem
Electrical light fixtures to be used at homes
    Lights Not Turning OnLights don’t turn on for six basic reasons:

1. The bulb is bad. This is more common than one might think. Try replacing a questionable light bulb with a new one. If that doesn’t work, before giving up, try using a bulb from another light fixture that you KNOW is working.

2. The switch to the light is bad. The switch will need to be replaced.

3. The light fixture is broken. Usually it is easiest and least expensive to simply replace the fixture. However, many light fixtures can be repaired if it is desired.

4. No power. Please go to the Power Problems section.

5. The time clock for the light is not set for the correct time or is broken. Re-set the time or replace the broken time clock.

6. If the light fixture is activated by a photo-cell, the photo-cell is out of adjustment or broken. Adjust or replace the photo-cell.

 Fluorescent, Mercury-Vapor, or High-Pressure-Sodium Lights. 

      These kinds of light fixtures all use an electrical ballast to energize their special light bulbs. If the light is humming loudly or has an “electrical odor,” or if the light just doesn’t turn on, the ballast may need to be replaced.
Lights Not Turning Off

1. The switch to the light fixture is broken. Replace the switch.

2. The time clock for the light is broken or out of adjustment. Set the time clock to the right time. If it won’t stay adjusted, replace the time clock.

3. If the light fixture is activated by a photo-cell, the photo-cell is either out of adjustment or broken. Adjust or replace the photo-cell.Lights Blinking On And OffThere are two main reasons for lights blinking on and off:

1. A photo-cell is out of adjustment. Adjust the photo-cell.

2. Some light fixtures that are recessed into the ceiling have a built-in thermal protector that automatically shuts off the light when the fixture gets too hot. Use a lower wattage bulb for a lower temperature.

Flickering Fluorescent Lights
   There are three reasons fluorescent lights flicker:
1. For a few moments when they first turn on, the bulbs will flicker until they warm up. You will notice this more on colder days. Just wait a few moments for the bulbs to warm up.

2. The fluorescent bulbs are old. Replace them.

3. The fluorescent ballast is old. Replace it.Bulbs Burning Out Too 

QuicklyHere are the three reasons bulbs can burn out quickly:

1. The wattage of the bulb is too high. This is very common. Most light fixtures with glass covers have a maximum rating of 60 watts per bulb. It is very common for people to put in 75 watt or even 100 watt bulbs. The result is bulbs burning out much too quickly. Use the correct wattage bulbs in all your light fixtures.

2. Poor-quality lights bulbs. Use only major-brand light bulbs.

3. Mysterious light fixture problems. It’s mysterious because the light fixture LOOKS perfectly fine, and even electricians can’t find anything wrong with it. Nevertheless, after checking #1 and #2 above, if the bulbs keep burning out…replace the light fixture.

Humming Lights
    Humming lights can be caused by:

1. A bad ballast or bad transformer. Replace the ballast or transformer.

2. A conflict between a low-voltage dimmer and the low-voltage light fixture it controls. This is a tough one, but sometimes experimenting with different dimmers will lead you to one that doesn’t make the low-voltage light transformer hum.Lights Dimming Lights will sometimes dim for a few seconds and then come back to complete brightness again. This can happen when a light is connected to the same wires that provide power to an appliance that takes a lot of power, like a refrigerator, a microwave oven, or an air conditioner. The reason the light dims for a few seconds is that the appliance is using a lot of power when it first starts up. After the appliance is running for a few seconds, it will use less power, and the light will return to normal again. If you have central air-conditioning, the lights may dim each time the air conditioning comes on.You will usually notice this dimming more at night (for obvious reasons!), but you might also notice it in the daytime. If this dimming bothers you, you can handle the problem by having an electrician add another circuit specifically for the appliance that is causing the dimming problem.NOTE: If you haven’t changed anything electrical in your home or office, and you suddenly start to have dimming problems or power fluctuations, then you probably have a loose wire somewhere. You should contact an electrician skilled in troubleshooting to find and correct this problem.


Electrical Dimmer to be used in lighting to adjust lighting intenisty       You might notice that sometimes a dimmer seems warm when you touch it. The good news is, THIS IS NORMAL. 
Dimmers naturally get warm when they are in use, especially if there is more than one dimmer in the same location.
However, if a dimmer is REALLY warm or hot to the touch, this indicates a safety problem, and you should call an electrician who is knowledgeable about lighting issues.Dimmer Warning – Two things to be careful about with dimmers:
  1. Never connect a regular dimmer to low-voltage lights, paddle fans, or any kind or motor. These devices require special dimmers.
  2. Never exceed the recommended wattage of the dimmer. Regular dimmers are rated for a maximum of 600 Watts. This is equal to 10 sixty Watt light bulbs, or 6 one hundred Watt bulbs.
NOTE: You can also buy higher-wattage dimmers for connecting more than 600 Watts to one dimmer.

Power Problems
          Receptacles Controlled By Switches In some homes and offices, a receptacle (outlet) on the wall is controlled by a light switch near the entrance to the room. This allows you to plug a lamp into the receptacle and turn it on and off with the switch.If an appliance that is plugged into a receptacle has no power, 

first turn on all the light switches in the room. Sometimes the device will come on, which means that it’s controlled by a switch.Hint: A receptacle usually has spaces for two plugs. Sometimes one is permanently energized and the other is controlled by a switch. This is known as a “half-hot” receptacle.

Electrical GFI( Ground fault interuptor) rec, to  to prevent electrical shocksGFI Receptacles In any location where there may be moisture (like kitchens, bathrooms, garages, and outdoors) special receptacles (outlets) are used for safety. These are called GFIs. 
The idea of a GFI receptacle is that with the slightest electrical problem, the GFI immediately shuts off the power. This is an important safety feature.
When you lose power to a receptacle in a kitchen, bathroom, garage, or outdoor area, check to see if it’s a GFI receptacle. There’s one pictured on this page. Click here for more information about GFI’s. If it’s a GFI, you can restore power by pressing the “TEST” button and then pressing the “RESET” button. If the GFI shuts off power repeatedly, plug in a different appliance to test whether the problem is the first appliance or the GFI itself. If the GFI is defective, call a good electrician.
Sometimes, you may have a receptacle that has lost power in a kitchen, bathroom, garage, or outdoor area but it’s not a GFI. It may be “protected” by a GFI that has tripped off somewhere else. 

You can check for this situation by making sure that all the GFIs in your kitchen, bathroom, garage, and outdoor areas are working properly.

More Technical Stuff About GFIsA GFI receptacle (also called a GFCI receptacle) can measure differences in power as small as 3ma (a very small amount). 

When the GFI detects more power coming in from the “hot” side than going out from the neutral side, it will shut off. This is a good thing because that extra electricity has to go somewhere, and it’s important to protect you and your family from it.All GFI receptacles should be tested monthly. This is done by pressing the “TEST” button. 

If pressing the “TEST” button does not make the button labeled “RESET” pop out, then call an electrician.

 If the “RESET” button does pop out, the GFI is OK. Press in the “RESET” button to reset the GFICircuit Breaker Tripped OffThe first thing to understand is that a circuit breaker can have tripped off even when it looks like it’s in the “ON” position. 

This is because a circuit breaker will sometimes trip off internally, without the “ON/OFF” handle flipping to the “OFF” position.

This is what to do when you have a loss of power that you suspect may be caused by a tripped circuit breaker.

1. Shut down any computer equipment that may be affected by a loss of power.

2. Go to your circuit breaker panel and firmly flip the first breaker OFF and then back ON again.

3. Do the same thing with each circuit breaker until you have flipped all of the circuit breakers OFF and then back ON again.

4. Now check and see whether the device that didn’t have power is now back on.

5. If your power has been restored… you’re done! If your power is still out, it’s time to call an electrician.

About 25% of all electrical power problems can be solved using the above technique. Good Luck!

More Technical Stuff About Circuit Breakers

Electrical circuit-breaker-diagram   Inside most circuit breakers there are two types of protection: 
One is thermal. The other is magnetic.
 The thermal strip measures heat build-up caused by overloading. When it reaches a certain temperature, it will shut off the breaker. 
The magnetic coil measures sudden increases in current (such as a short). 
At a predetermined limit it will shut the breaker off. Older breakers sometimes have only one of these features. For maximum protection, a breaker with both types of protection is recommended.There are usually three spots on the outside of a breaker that show wear. If the “ON/OFF” switch (located at the top) has broken off or is loose, we recommend the breaker be replaced. 

Next is the load lug. If it is burnt or abnormally loose, we recommend the breaker be replaced.

 Last, and most common, is the stab. The breaker stab is what makes contact with the bussing in the panel (the bussing carries the power throughout the panel). 

The stab connects to the bussing through friction and spring tension. The spring tension, over time, may break down. If so, arcing or burning may result. 

If the stab has become burnt, discolored, or is abnormally loose, we recommend that the breaker be replaced and that the bussing in the panel be checked.

NOTE: It is possible for a breaker to appear OK in regard to it’s outward appearance and its capacity to carry continuity, but still be questionable, bad, or intermittent. The opposite may be true as well. 

A breaker with a poor outward appearance may be perfectly safe and structurally sound. 

Therefore a decision to replace a breaker should not be based solely on appearance, continuity, age, etc.

 A good electrician can recommend the proper course of action based on taking into account all the relevant factors.

Short Circuits 

   Short Circuits occur when two electrical wires accidentally touch each other. 

A short circuit will immediately cause one of your circuit breakers to trip off or one of your fuses to blow.

To fix a short circuit, ask yourself this question: “What was happening right before the short circuit?” If you had just plugged something into a receptacle (outlet) or turned on a light or an appliance, then this gives you a clue.

If you just plugged in an iron, for instance, you can simply un-plug the iron and then re-set the circuit breaker or replace the fuse.

 If everything is now OK, then your electrical system is fine and it’s time to get a new iron!If, however, you can’t find an appliance which is causing the problem, then it’s time to call a good electrician to locate and repair your short circuit.No Power At All

When nothing works in the entire building this means:

A. The electrical power from the utility company is not getting to your electrical panel. 
Call the utility company.

B. The electrical power from the utility company is not getting to ANYBODY’S electrical panel. 
Wait for the utility company to restore power.

C. Your main circuit breaker is broken or turned off. Try to re-set the circuit breaker.

D. All your circuit breakers are flipped off. Re-set all breakers.E. 

Something else. Time to call an electrician.


Electrical fuses to be used at homesanother kind of fuses to be used wiyth large load


    When a fuse detects too much power running through a wire, a tiny piece of metal inside the fuse will break, thereby stopping the power from continuing to run through the wire.
When the top of the fuse is made of glass, many people think that they can look at the metal piece inside and see if it is broken.
The best way to handle a suspected blown fuse is to simply replace it. 
If the power comes back on, great! If it doesn’t, then you should call an electrician who is good at troubleshooting.

Website Builder provided by  Vistaprint